Welcome to the Honda Trail 125 Forum! We are an enthusiast forum for the Trail 125, Hunter Cub, CT125 or whatever it's called in your country. Feel free to join up and help us build an information resources for this motorcycle. Register a free account today to become a member. Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members through your own private inbox!
Excellent! I need to order a service manual.According to the wiring diagram at the back of the service manual, 12v power to both is white/black; low beam is white; high beam is yellow/white; and ground is green.
Just curious, what are you trying to do? I've got a suggestion for connecting a USB charger that turns on & off with the key.
Sounds like a great mod. I'm sure we'll see photos posted of the finished project.Excellent! I need to order a service manual.
I just mounted a set of fog lights and instead of using a switch I want to tie them directly to the high beam instead. I have the relay installed and everything up and running, I just needed to know which ones were the ground and high beam.
That probably depends on what the expected draw is of whatever you're adding. Any idea?Fun4me, what is your suggestion for switched power supply?
Fun4me said he has a suggestion, but I would think tapping the low beam wire (white) would work just fine.USB port for sat nav or phone charging
Here's how I connected my USB charger port so it turns on only when the ignition is on. Key off so no need to disconnect the battery. Removed headlight ring, disconnected the headlight using the small gray connector (not visible in the photo) and set it aside. Made a small cut in the electrical tape to easily access the black/yellow wire going to the larger black connector in the center of the photo. Used a blue size Posi-Tap connector to attach the red (positive) wire to the black/yellow wire. Used another Posi-Tap connector to attach the black (negative) wire to the green (ground) wire going to either of the turn signals, located in their separate two wire connectors. I chose the one on the right. The one on the left is also clearly visible in the photo. Reassemble and It's a simple, five minute job.That was my thought. Did wonder if there was an alternative I hadn’t considered.
TrailBoss, I've attached a scanned file of that section of the wiring diagram from the Service Manual. I'm sorry, but may have told you wrong. If you look at the bottom 'dimmer switch' section it shows white for low and yellow/white for high. However, at the 'headlight' section on the left it shows white for high and white/yellow for low. I'm truly sorry for causing confusion with bad info.@Fun4me, are you certain yellow/white is high beam? I tapped it as well as green, but I'm getting 0v. Yes, I am trying this with the motor running and the high beam switch on.
No harm at all. That's what forum are for, information, sometimes good, sometimes bad, but always helpful!TrailBoss, I've attached a scanned file of that section of the wiring diagram from the Service Manual. I'm sorry, but may have told you wrong. If you look at the bottom 'dimmer switch' section it shows white for low and yellow/white for high. However, at the 'headlight' section on the left it shows white for high and white/yellow for low. I'm truly sorry for causing confusion with bad info.
Yeah, that's what I'd do too. Electrical stuff has always been FM (f--king magic) to me. Thought the wiring diagram would help but it still looks like a bowl of spaghetti. Good luck.I think my idea is a bust.
I checked White, White/Black, Blue, Yellow/White... The one that APPEARS to do what is needed is the white wire. It changes voltage based on the high beam switch. HOWEVER, the problem seems to be that even in the low beam position, the white wire is still putting out about 8v, and that's enough to trip my relay and turn on the lights. With high beam on it puts out 14.4v, which trips it as well, as expected.
My guess is since this is an LED headlight system they were able to take some liberties with threshold voltage that you normally wouldn't be able to do in an analog system. So 8v isn't enough to reach the LED threshold and turn the high beam on, but it won't work in my particular situation.
I think at this point I'm punting and I'm just going to get a handlebar mounted switch and be done with this. Unless we have some electrical engineers around here that might have some explanation to this electrical devilry!
Good to know. I'm only using it to charge my phone or GoPro so don't know if that will be an issue. RPMs will be fairly high most of the time which should be enough to keep them charged. I'll keep an eye on it and come up with a plan B if necessary.Fun4me, took the power from the Black/Yellow as you suggested. Seems that looking at the wiring diagram the power to the headlight is from the rectifier and not the battery direct so more likely to fluctuate with the rpm.