20+ Mods Applied, More to Go!!! (Pictures)

[op46]

So finally got all the modifications done I was wanting. Still two minor to do. A RAM X phone grip with tough claws and a handle bar support bar. Counting up I have about 20 mods applied and a few of them count as two items and some are just adjustments or moving stock items positions. The three pictures show the LRD (black) with all applied. I have a few to do on the LRD (red) to apply yet. I will let you try and figure out the mods and put up a list in a few days to check against your guess. I will help with the ones you cannot see or discern from the pictures. 1. OPMID Speedo/Tac, 2. Kick Stand base-plate (color coded), 3. Key slot bezel (color coded), 4. Invoxia GPS tracker in tool box, 5. DIN plug charger, 6. Handle Bar riser, 7. Shifter support bearing assembly. That leaves 13 some of which are multiples of 2.

 

[FleaMike]

Just did a Velcro job on my JBL speaker. Did a cruise around town listening to Leftover Salmon at high volume.

 

[G19Tony]

I've got a few of those Twisted Throttle stickers. That's a good spot for one.

 

[rdkeith]

So finally got all the modifications done I was wanting. Still two minor to do. A RAM X phone grip with tough claws and a handle bar support bar. Counting up I have about 20 mods applied and a few of them count as two items and some are just adjustments or moving stock items positions. The three pictures show the LRD (black) with all applied. I have a few to do on the LRD (red) to apply yet. I will let you try and figure out the mods and put up a list in a few days to check against your guess. I will help with the ones you cannot see or discern from the pictures. 1. OPMID Speedo/Tac, 2. Kick Stand base-plate (color coded), 3. Key slot bezel (color coded), 4. Invoxia GPS tracker in tool box, 5. DIN plug charger, 6. Handle Bar riser, 7. Shifter support bearing assembly. That leaves 13 some of which are multiples of 2.View attachment 1079View attachment 1080View attachment 1081

How difficult was the Opmid to install? Does it come with English instructions?

 

[op46]

How difficult was the Opmid to install? Does it come with English instructions?

Not hard it self. Getting all the covers off to access the wire harness and run temp sensor and solenoid Y wire a pain with all the different types of bolts and snap connectors some of which are hidden. Yes instructions in English and pretty clear. Programming it a snap once you figure out the button push count to put in different modes. Watch the YouTube videos on it. Plus a section on this site on install too.

 

[op46]

I've got a few of those Twisted Throttle stickers. That's a good spot for one.

Really high reflective. I got 4 when I ordered my fuel bags.

 

[op46]

OK here is the list of mods on the LRD in the picture:
1. Headlight Protector bar
2. Tool Bag Bracket over headlight
3. Keni Moto Waterproof Front Tool Bag
4. Extended oblong black mirrors
5. Grip Puppies
6. OPMID Speedo/Tac
7. Key Ring Bezel (color coded)
8. DIN Plug Charger
9. Engine Crash Bars
10. Muffler Crash Bar
11. Back Rest Kuriakin
12. Milwaukee Packout Crate, baseplate and wood top, (also have large toolbox)
13. Keni Moto Rear Ballistic Nylon Tool Bag
14. Metal Chain Guard (color coded)
15. GPS Tracker in Tool Box
16. Kick Stand Base Plate (color coded)
17. Shifter Support bearing assembly
18. Handle Bar Riser with bar clamp rotated forward
19. Horn Cover
20. Seat Rear Bar Foam Cover
21. Handle bar grip shields
22. Handle Bar Rotated to vertical.
23. Handle Bar Bracket rotated forward
24. Front Shifter clocked higher one notch, lowering rear shift pedal.